Find the default login, username, password, and ip address for your Linksys DD-WRT router. You will need to know then when you get a new router, or when you reset your router.

From here you can just log into the web GUI of the dd-wrt router from the address that you used (192.168.0.1) and set it up however you like. To change any settings in your Verizon AT router you still just use the default IP address 192.168.1.1 . After installing DD-WRT Firmware you can access the DD-WRT Web-GUI using a web browser pointing to the same IP address as before you installed DD-WRT. These are some of the most common default IP addresses: 192.168.1.1 (most commonly used on Linksys and Asus), 192.168.2.1 (some Belkins), 192.168.11.1 (some Buffalos), 192.168.10.1 or 192.168.30.1 (some Motorolas), and there may be others. For example, if the router default address is 192.168.10.1, set the computer IP manually to 192.168.10.77 with 192.168.10.1 as the gateway. Power the router on with a continuous ping running in a command window: ping -t If you still receive no response, the IP address may have been changed from the default. Disconnect all other machines from the router and run arp in a command window to find out what the IP address is: arp -a Find the default login, username, password, and ip address for your Linksys DD-WRT router. You will need to know then when you get a new router, or when you reset your router. How to factory reset DD-WRT. Press and hold the reset button of the router for at least 20sec. Release the button once the router restarted. Now the router will be reconfigured to factory default settings. Now you can connect the router in Telnet @192.168.1.1 with default username and password (root/admin). Firmware: DD-WRT v3.0-r29440 std (04/11/16) Kernel: Linux 4.4.7-rc1 #604 SMP Mon Apr 11 05:42:18 CEST 2016 armv7l Status: ok Reset: yes (after flashing, reset to default settings) Errors: Limited Connectivity on the Virtual Guest AP (on wl0.1). Clients can connect to the AP, but its IP address is 169.254.x.y. DNSMasq seemingly fails to respond.

Setup via DD-WRT Script . 1. In the DD-WRT Administrative Interface, navigate to Setup > Basic Setup. Under Network Address Server Settings (DHCP), set these NordVPN DNS addresses: Static DNS 1 = 103.86.96.100 Static DNS 2 = 103.86.99.100 Static DNS 3 = 0.0.0.0 (default) Use DNSMasq for DHCP = Checked Use DNSMasq for DNS = Checked DHCP

Setup via DD-WRT Script . 1. In the DD-WRT Administrative Interface, navigate to Setup > Basic Setup. Under Network Address Server Settings (DHCP), set these NordVPN DNS addresses: Static DNS 1 = 103.86.96.100 Static DNS 2 = 103.86.99.100 Static DNS 3 = 0.0.0.0 (default) Use DNSMasq for DHCP = Checked Use DNSMasq for DNS = Checked DHCP DD-WRT Router OpenVPN Setup 1. Point your web browser to your DD-WRT Administration Page, which the default LAN-side router address, the gateway address of the

To get past this issue, simply set your computer's IP address and subnet to 192.168.1.8 and 255.255.255.0 respectively. (This assumes you are still using the default settings. If not, change the IP address and subnet as appropriate) You should now be able to point your browser at 192.168.1.1 (again assuming default settings). [ edit ] LAN Uplink

After installing DD-WRT Firmware you can access the DD-WRT Web-GUI using a web browser pointing to the same IP address as before you installed DD-WRT. These are some of the most common default IP addresses: 192.168.1.1 (most commonly used on Linksys and Asus), 192.168.2.1 (some Belkins), 192.168.11.1 (some Buffalos), 192.168.10.1 or 192.168.30.1 (some Motorolas), and there may be others. For example, if the router default address is 192.168.10.1, set the computer IP manually to 192.168.10.77 with 192.168.10.1 as the gateway. Power the router on with a continuous ping running in a command window: ping -t If you still receive no response, the IP address may have been changed from the default. Disconnect all other machines from the router and run arp in a command window to find out what the IP address is: arp -a Find the default login, username, password, and ip address for your Linksys DD-WRT router. You will need to know then when you get a new router, or when you reset your router. How to factory reset DD-WRT. Press and hold the reset button of the router for at least 20sec. Release the button once the router restarted. Now the router will be reconfigured to factory default settings. Now you can connect the router in Telnet @192.168.1.1 with default username and password (root/admin). Firmware: DD-WRT v3.0-r29440 std (04/11/16) Kernel: Linux 4.4.7-rc1 #604 SMP Mon Apr 11 05:42:18 CEST 2016 armv7l Status: ok Reset: yes (after flashing, reset to default settings) Errors: Limited Connectivity on the Virtual Guest AP (on wl0.1). Clients can connect to the AP, but its IP address is 169.254.x.y. DNSMasq seemingly fails to respond.